| KRUZER KADDY |
| #500 • Chrome KUSTOM KADDY Mounts to Harley Davidson & Gold Wing switch housings, either side. $40.00 |
| #300 • Black KRUZER KADDY * $40.00 |
| The KRUZER KADDY is a unique accessory for the motorcycle or ATV. It can be used to hold beverages, sunglasses, cell phones, radios, etc. The KADDY has also been placed on walkers for the elderly or a recovering patient. • Included are two foam inserts which accommodate various sizes of drink containers such as 12 oz. can, 16 oz. bottles, and 20 oz. bottles. • Fits most 7/8" to 1" handlebars. • Each is individually boxed and comes with an allen wrench for easy assembly. • Easily detachable from chrome-plated steel bracket. • Grommet is included to secure cup if desired. • Available in Chrome, Stainless Steel, Leather Wrap, and Camouflage. The KUSTOM KADDY takes the original KRUZER KADDY and includes all hardware necessary to mount on switch housings on Harleys as well as Gold Wings instead of clamping on the handlebar. |
| Kamo |
| Leather Wrap |
| #100 Satin Finish KRUZER KADDY * $36.00 |
| STEP ONE: Choose the location on the handlebar where you want your KRUZER KADDY located. It is best to locate the chrome handlebar clamp on a straight portion of your handlebars, as the bending process used by the handlebar manufacturers deforms the shape of the bars and may cause the clamp to not fit properly. Be sure to choose a location that is high enough on the bars to insure clearance between the bottom of the KRUZER KADDY and the fuel tank. The mounting stud maybe placed either above or below the handlebar. Using the supplied allen wrench, attach the bracket onto the handle bar. STEP TWO: Attach the cup to the bracket by placing the grooved bracket tip into the keyhole located on the side of the cup. Slide the cup down onto the bracket. STEP THREE: Insert the rubber grommet into the lower portion for the cup keyhole. This will secure the cup to the mounting stud. When using the KRUZER KADDY on 7/8th diameter bars, a split-plastic busing is supplied with each KRUZER KADDY. Spread the bushing apart and slip it over the 7/8th bar. Then place the handlebar clamp over the plastic bushing and squeeze the two clamp halves together. The clamp screws may now be tightened and the cup can be attached as per STEP TWO and STEP THREE above. KRUZER LLC recommends the use of the rubber grommet to secure the cup to the mounting stud. This will insure that the cup does not dislodge should you hit a rough pothole or other road obstacle. This is especially true for ATV or off-road riding. Each KRUZER KADDY comes with 2 removable insulated liners. The thick liner is for 12oz cans or 16oz water bottles and the thin neoprene liner is for 20oz soda or water bottles. One liner must be removed for the other to be used. |
| STEP 1 |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| COPYRIGHT 2012 HUNCH FURS, LLC |
| #200CH • Chrome KRUZER KADDY Fits 7/8, 1, and 1 1/4 inch bars. This model also has a rigid mount option which will not allow the cup to pivot per instructions. $45.00 |
| #400L • Leather Wrap KRUZER KADDY Fits 7/8, 1, and 1 1/4 inch bars. This model also has a rigid mount option which will not allow the cup to pivot per instructions. $52.00 |
| STEP 2 |
| STEP 3 |
